Tag Archives: Roasts

A tale of three roasts

This is an experiment to compare three different roast levels of Colombia Timana de Huila.  This first roast is the “calibration roast”.   Full power to first crack then roasted to the first snap of 2nd crack. In this roast, first crack started at 725 seconds and stopped 114 seconds later.  Second crack started at 355 seconds after first crack.



I stopped the second roast 295 seconds after first crack.  A full minute shorter than the first roast.  First crack started at 695 seconds and ended 111 seconds later.  I forgot to remove the outlet vent duct from the outlet until about 200 seconds into this roast.  You can really see the significant affect this has on the inlet temperature.  Outlet and Bean Mass temps are much less affected.



I stopped the third roast 235 seconds after first crack — a full two minutes less than the calibration roast.  I got distracted on this roast and, although I remembered to remove the outlet vent duct before I started the roast, I forgot to turn up the outlet setpoint to 550F at the beginning of the roast and I also forgot to set the post first crack temp up to 510F.  I really need to get the automatic roast profile setup completed for the RoastGenie.  It looks like I caught the initial setting error before it made any difference.  The post first crack setpoint mistake did result in the bean mass temperature dropping a bit. First crack on this roast lasted between 120s and 132s compared to about 111-114s for the previous roasts.


Guatemala Acatenango Gesha


Roasted this on October 14th.  This bean has an amazing first crack — like a popcorn popper!  Lots of the Guatemala I have been roasting lately has a nice defined first and second crack but nothing like this.  Wow.  I stopped this one before 2nd crack in an attempt to keep it at a city + roast.  First tasting will be tomorrow.  I am excited to try  this one.

More experimentation with Guatemala Huehuetenango Cuilco

Last weekend I did a series of roasts with small batches of Guatemala Huehuetenango Cuilco.  One important thing that I have learned about this coffee is that it takes quite an aggressive roast profile to obtain the best tasting coffee — more time and higher temperatures.  I think that this might be somewhat characteristic of Guatemalan coffees but I’m not sure exactly which parameter is important (origin, altitude, farm, etc..).  The best roast so far was one that had an extended drying time and was roasted into 2nd crack at an outlet temperature setpoint of 510F throughout the roast.

This weekend’s experiment is two different roasts of this coffee – both into second crack but one with an extended drying time and one without.  The roast profile for the extended drying time roast is below.  Unfortunatly I had a problem with the Roast Genie that caused me to lose the data for the 2nd roast.  The profile is the same but the 350F dwell time is missing from this second batch.



The second roast went 968 seconds, 319 seconds past first crack with 18.5% mass lost.  In contrast the first roast was 1052 seconds, 300 seconds past first crack with 19.0% mass lost.  Both were 150g batches (green weight) and were less than 30s into 2nd crack.

One of the nice things about this coffee is that 1st and 2nd crack are very distinct.  This is one of the easiest coffee’s to identify these stages that I have experienced.

I will add tasting notes over the next few days…


Roast Profile Experimentation – Guatemala Huehuetenango Cuilco

The second generation Roast Genie is nearing completion.  This weekend, I roasted seven different 100 g batches of Guatemala Huehuetenango Cuilco to begin to get a feel for how the new roasting system is going to work.


The first thee batches were roasted Friday with different durations of roast time past the onset of first crack.  For these I roasted at an initial set point of 510 F (environmental temperature at roast chamber exit) and then backed down to 490 F once 1st crack started.

Roast 1 – 3 min past onset of 1st crack (16.8% mass lost)


 Roast 2 – 3 1/2 min past onset of 1st crack (15.0% mass lost)

Roast Profile 2


Roast 3 – 4 min past onset of 1st crack (15.6% mass lost)



General observations during roasting:

First crack was very pronounced with this coffee.  Onset was consistent from batch to batch starting at about 640 to 650 seconds into the roast.  Darkening of the roast was not all that pronounced from the 3 min to the 4 min roast as it sometimes is with other beans.  Although I don’t think the roast stalled, the frequency of cracks did not seem all that high.  It seems like this bean can take quite a bit of heat before significant changes take place.  The change in bean mass during roast was a little unexpected with the lightest roast having the highest loss in mass.  This is probably due to the fact that I am roasting such small quantities that the measurement error is significant (+/- 2g measurement error = +/- 2% mass lost error).

Tasting notes:

None of these roasts were particularly impressive displaying a significant lack of body even after 36+ hours of rest.  I perceive there to be significant sweetness and acidity in the cup but there is also an astringency in the finish and general lack of body that I find unpleasant.  My suspicion is that these are under-roasted. I also noticed that the beans sound much harder or denser in the grinder than the Yemen beans I have recently been using.  Those bean seem very soft and these much harder — at least in comparison.  The Yemen beans  developed in the roaster much faster than these seem to.

I completed the next four roasts today and attempted to adjust the profile to stretch out the roast a little in the hopes of allowing a little more body to develop.  After reading this post on Stretchin’ Out the Roast at Sweet Marias and watching this video, I decided to extend the drying time by adding a 2 minute dwell at 350 F during initial heating.  I roasted three batches with post first-crack times of 3 1/2 minutes but used three different post first-crack temperatures: 490 F (like roasts above), 500 F and 510 F.  After observing less impact on this bean than I had expected. I roasted a fourth batch with a 3 minute dwell time at 350 F, 510 F post first-crack temperature and just about 5 minutes past initiation of first crack.  For this roast, 2nd crack had just started.

Roast 4 – 3 1/2 min past onset of 1st crack @ 490F. Includes 2 min dwell @ 350 F drying time (16.8% mass lost).


Note that this roast profile shows 1st crack happening about 100s earlier than it should — for some reason there was a single bean crack at 580s or so but then nothing for another 100+ seconds.

Roast 5 – 3 1/2 min past onset of 1st crack @ 500 F. Includes 2 min dwell @ 350 F drying time (17.0% mass lost)


Roast 6 – 3 1/2 min past onset of 1st crack @ 510 F. Includes 2 min dwell @ 350 F drying time(17.0% mass lost)


Roast 7 – 5 min past onset of 1st crack @ 510 F.  Includes 3 min dwell @ 350 F drying time (18.0% mass lost)


General observations during roasting

Again – I was rather surprised by how “robust” this bean seemed during roasting.  Changes in roast time and temperature that I would have expected to dramatically impact other beans seemed to have much less impact on these.  The 7th roast in particular was surprising in that the beans were not more significantly darkened. I have had trouble getting the results I wanted from Guatemala beans in the past and wonder now if more heat is required to get the desired roast levels.   I will add tasting notes tomorrow after I have had a chance to begin sampling.

Thoughts on the Roast Genie system

Overall the 2nd generation system is working well but I have a ways to go to get all of the automated posting completed.  The camera for taking pictures of beans after roasting still needs to be completed but the automated preparation of plots is working pretty well.

I had anticipated that having one pre-crack temperature setting and one post-crack temperature setting with manual control of the post-crack time would be sufficient control over the roast profile.  After the experience here with this Guatemala, I think I may need to allow easier adjustment of these profiles.